The Stain Library

How to remove baby sick from quarry tile

  • DifficultyModerate
  • OutlookOften removable
  • MaterialQuarry tile
  • Reviewed7 September 2026

The short answer

Blot and lift the solids quickly, because a quarry tile is unglazed and absorbs like the grout beside it. Wash with warm water and a mild neutral detergent and work the textured surface with a soft bristle brush. The manufacturer warns specifically against no rinse enzymatic and acid based cleaners, because with heat and food contamination they make the grout soft and permanently damage it.

If it has just happened

Blot immediately and lift the solids. Both the tile and the joint absorb here, so unlike a glazed floor the clock is running from the first second.

Heat can set this stain permanently

Do not use hot water, a tumble dryer, an iron or a steam cleaner until the mark has gone. Heat fixes this type of stain into the fibres and makes it far harder to shift.

Test on a hidden area first

Try any cleaner on a hidden part of the material first, such as a seam, an offcut, inside a hem or under a piece of furniture. Wait for it to dry and check for colour change before treating the visible mark.

Cleaning the mark is not the same as disinfecting

If the sickness came with a stomach bug rather than an ordinary posset, the surface may carry norovirus, which spreads easily and survives on hard surfaces. UK public health guidance is to wear gloves, avoid shaking contaminated laundry, wash affected laundry separately with normal powder at 60 C where the care label allows it, and disinfect compatible hard surfaces with a bleach based product afterwards. Do that after the stain work, not instead of it, and only where the material tolerates it.

Keep every kind of drying heat away until the mark has gone

Baby sick is mostly milk protein. Heat coagulates protein and locks it into the material, which is why a mark that would have washed out can become permanent after one hot wash, one pass with an iron, a hairdryer or a spell on a radiator. Cool or warm treatment, air drying, and a proper look in daylight before anything warm goes near it.

What you will need

  • Disposable gloves Sickness that came with a stomach bug is a hygiene job as well as a stain.
  • A plastic scraper or spatula Plastic, so it does not scratch a glaze or score a soft grout line.
  • Kitchen roll and cloths For lifting the bulk before anything is spread about with a mop.
  • Warm water and washing up liquid A mild neutral detergent is what tile makers specify for routine cleaning.
  • A soft bristle brush For grout lines and textured tile, where a flat cloth passes over the surface.

Helpful but not essential

  • Bicarbonate of soda A mild paste for grout and unglazed tile, which needs no acid and no bleach.

Fresh baby sick on quarry tile

Lift the bulk before you introduce any water, because water spreads it into the joints.

Go carefully with warm water

Quarry tile tolerates warm water only within limits. Keep contact time short, work from the edge of the mark inwards and stop if the material changes.

  1. Lift the solids with a plastic scraper

    Plastic rather than metal, so a glaze is not scratched and a soft grout line is not scored. Take it straight to a bag rather than pushing it along the floor.

  2. Blot the liquid up before mopping

    Kitchen roll pressed down. Mopping first simply carries the spill into every joint within reach.

  3. Wash with warm water and a little washing up liquid

    A mild neutral detergent, which is what tile makers specify. Not an acid and not a bleach based product, because both attack cementitious grout.

  4. Work the joints, then rinse and dry

    Work the textured surface and the joints with a soft bristle brush and warm soapy water, which is what the maker specifies, then rinse and dry the floor thoroughly.

  • How longTen minutes
  • RepeatingRinse and dry rather than repeating.
  • Stop ifthe tile and the joints are clean and the floor has been dried

Dried baby sick on quarry tile

The tile face is easy. The joints are where the work is.

Go carefully with warm water

Quarry tile tolerates warm water only within limits. Keep contact time short, work from the edge of the mark inwards and stop if the material changes.

  1. Soften the residue rather than scraping it

    Warm soapy water left on the mark for a few minutes lifts dried milk off a glaze completely and loosens it in a joint.

  2. Brush the joints with a soft brush

    Along the joint rather than across it, with light pressure. Hard brushing removes the surface of the grout and makes it more absorbent, not cleaner.

  3. Use a bicarbonate paste in a stubborn joint

    A little bicarbonate of soda mixed with water into a paste, worked into the joint with a brush and left for ten minutes, then rinsed. It is mildly alkaline, which is what grout tolerates.

  4. Rinse thoroughly and dry the floor

    The tile trade warns that alkaline cleaner not properly rinsed leaves a sticky residue that attracts dirt, so the rinse matters as much as the clean.

  • How longHalf an hour
  • RepeatingTwo passes on the joints rather than one hard one.
  • Stop ifthe joints are as clean as the ones around them and the floor is dry

Old or set in baby sick on quarry tile

An old mark on tile is nearly always in the grout rather than on the tile.

Go carefully with warm water

Quarry tile tolerates warm water only within limits. Keep contact time short, work from the edge of the mark inwards and stop if the material changes.

  1. Work out whether it is the tile or the joint

    Wet a finger and rub the tile face. If the tile is clean and the line between tiles is not, the problem is the grout and cleaning the tile harder achieves nothing.

  2. Give the joints a longer soak

    A bicarbonate paste left on the joint for half an hour, then brushed and rinsed, reaches further than a quick scrub. Repeat rather than pressing harder.

  3. Consider that grout is renewable

    Raking out the top few millimetres of a grout line and refilling it is a normal, inexpensive job, and it produces a result no cleaner can. On a small area it is well within a competent DIY afternoon.

  4. Seal it afterwards

    The tile trade recommends sealing cementitious grout to prevent staining. New or freshly cleaned grout is the right moment, and it is what stops the next spill doing the same thing.

  • How longAn hour, then a decision
  • RepeatingTwo attempts, then consider regrouting.
  • Stop ifthe joints look even, or they need regrouting or a specialist

What not to use on quarry tile

  • Acidic cleaners, including vinegar and limescale removers, on the grout

    The tile trade body says grout manufacturers do not advocate acids because acids attack the cement in the grout, which is alkaline based and is dissolved by them. A tile floor is mostly grout by exposed edge length, so acid on the tile means acid on the grout.

  • Scouring powder, wire wool and abrasive pads

    They scratch a glaze permanently and take the surface off unglazed tile, leaving a rougher patch that then holds dirt and looks dirtier than before.

  • Leaving the floor wet after cleaning

    Water sits in the grout joints, and the joint is the porous part. A tiled floor is dried rather than left to evaporate, which is what tile makers specify.

  • A steam cleaner on the joints

    Steam forces moisture and heat into the grout and any sealer on it, and heat sets milk protein at the same time.

  • No rinse enzymatic floor cleaners

    The tile maker names these alongside acid based cleaners as the combination that, with heat and food contamination, makes quarry tile grout soft and permanently damages it.

White compared with coloured quarry tile

Quarry tile is usually a strong red or brown, fired through, so the tile colour does not change. What changes is the sealer: acidic and bleach based cleaners strip it, and the area then absorbs faster than the rest of the floor and looks progressively darker with use. That is the fault to design against, because it develops slowly and is easy to miss until the floor is patchy.

If the mark is still there

Look at the floor dry and in daylight. An unglazed floor darkens noticeably when damp and takes time to return to its normal colour.

If a shadow has soaked into the tile itself, a bicarbonate of soda poultice works exactly as it does on stone: a paste spread over the mark, covered, and left for a day.

If the floor no longer beads water, the sealer has gone and the tile is unprotected. Stripping and resealing a quarry floor is standard work, it is what a tired floor actually needs, and it does more for its appearance than any amount of cleaning.

When to stop and call someone

Get a tile specialist in rather than continuing if the tile itself has stained through a worn sealer, if the grout has gone soft, which is what acid or no rinse enzymatic cleaners do to it, or if two poultices have failed. Stripping and resealing a quarry floor is standard work and is what a tired floor actually needs.

Why baby sick behaves this way on quarry tile

Quarry tile is unglazed extruded clay, traditionally red, common in older kitchens and utility rooms.

The tile absorbs too

Which is the difference from a glazed floor. There are now two porous materials rather than one, and the tile face is the larger area of the two.

The maker's warning is specific and useful

Daltile names no rinse enzymatic cleaners and acid based cleaners as the combination that, together with heat and food contamination, makes the grout soft and permanently damages it. In a kitchen, all three are present.

The surface is textured

So a flat mop passes over the low points and a soft bristle brush is specified. That is also why quarry floors hold dirt in a way a smooth floor does not.

Sealing is part of the specification

Applied before grouting and repeated regularly, which tells you resealing is routine rather than a repair.

Sources

What we checked and when. Where a manufacturer instruction disagrees with anything here, follow the manufacturer.

  1. Cleaning grout, Tile Council of North America trade body

    Tile trade body guidance that grout manufacturers do not advocate the use of acids because acids attack the cement in the grout, that grout is alkaline based and is dissolved by acids, that mildly alkaline cleaners are preferred over acidic ones, that oil and wax based cleaners leave a film that attracts dirt, that alkaline cleaner not properly rinsed leaves a sticky residue, and that cementitious grout should be sealed to prevent staining.

    Checked 7 September 2026

  2. Quarry tile care and maintenance, Daltile manufacturer

    Tile manufacturer guidance that quarry tile is sealed before grouting and resealed regularly to protect against staining, that routine cleaning is multi purpose products or plain soap and water, that no rinse enzymatic and acid based cleaners are avoided because the combination of heat, food contamination and cleaner makes the grout soft and permanently damages it, and that a soft bristle brush suits the textured surface.

    Checked 7 September 2026

  3. Sick happens: how to get vomit out of carpet, National Carpet Cleaners Association trade body

    UK carpet cleaning trade body method for vomit: scrape solids with a blunt spatula or spoon, apply equal parts white vinegar and water, blot gently working towards the middle of the mark rather than outwards, never scrub because that drives the vomit deeper and damages the carpet, use only a small amount of warm water on a dried mark, and expect rehydrating it to release the smell again so ventilate.

    Checked 7 September 2026

  4. How to remove baby formula stains, Purex Stain Lab manufacturer

    Manufacturer guidance identifying breast milk, formula and baby spit-up as protein stains, explaining the role of enzymes, and warning that the mark should be checked before any drying heat because heat sets what remains.

    Checked 7 September 2026

  5. Norovirus: what to do and how to stop the spread, UK Health Security Agency authority

    UK public health guidance establishing that illness related vomit can carry norovirus, that contaminated laundry should be washed with normal powder at 60 C where the care label permits, and that compatible hard surfaces should be disinfected with a bleach based product.

    Checked 7 September 2026